#Logged in as pi user but startx doesnt work how to
#Logged in as pi user but startx doesnt work install
#Logged in as pi user but startx doesnt work drivers
#Logged in as pi user but startx doesnt work update
#Logged in as pi user but startx doesnt work password

#Logged in as pi user but startx doesnt work install

Now you can use yum to install all the stuff you want. Raspi-redsleeve-gui-0.3.1.img.xz – 359Mb – Desktop versionĢGb is a bit limiting, but you can use gparted to resize the ext4 partition up to whatever your SD card will accommodate. Raspi-redsleeve-cli-0.3.img.xz – 226Mb – Command Line version There are also a ‘xz’ compressed versions if you can handle that – it contains the same images as above. Raspi-redsleeve-gui-0.3.1.img.gz – 537Mb – Desktop version Raspi-redsleeve-cli-0.3.img.gz – 318Mb – Command Line version Be very careful to set the SD card location correctly, otherwise you could destroy a hard disk! Type ‘dmesg’ and you should see the SD card location at the end of the listing, if it was the last thing you plugged in.Īlternatively you can use the fedora-arm-installer available here: #dd if=/source_directory/raspi-redsleeve-gui-0.3.1.img.gz conv=noerror,sync bs=8M | gzip -dcf | dd of=/dev/sdf bs=8MĪlter your source directory and SD card location (/dev/sdf) to suit. To use the desktop image (in linux) type: It is optimised for using a monitor – if you use a TV and have overscan issues you need to edit /boot/config.txt and alter the line ‘disable_overscan=1’ to ‘disable_overscan=0’ and reboot. Once logged in as ‘pi’ simply type ‘startx’ to fire up the desktop if you’re using the desktop version. They will connect to a network using DHCP.

#Logged in as pi user but startx doesnt work password

They both contain a user account for ‘pi’ password ‘raspberry’ and the root account has a password of ‘redsleeve’. To simplify the process I have prepared a couple of 2Gb card images that can get you started. The way this was achieved was to take one of the current Raspberry Pi Debian images and replace the main partition from the rootfs currently available on the RedSleeve site. So if all the above suggestions fail, you could try buying a new mouse or simply try a different one if you have one. Console Autologin Text console, automatically logged in as pi user Desktop Desktop GUI, requiring user to login Desktop Autologin Desktop GUI, automatically.

#Logged in as pi user but startx doesnt work drivers

Note: it has been reported that these images do not work on the V2 Pi boards.Īs I don’t have one to test I suggest you try the alternative install method as outlined on the RedSleeve Wiki Page – Debian doesn't have drivers for every piece of hardware, and if Debian doesn't have the right driver for your mouse then in my experience (limited to my one example) it simply won't open the GUI.

#Logged in as pi user but startx doesnt work update

This latest update now comes in two versions, one a basic command line setup while the other has a basic desktop available. If you are attempting to use Twister OS on a Raspberry Pi 3B/3B+, and are taken. RedSleeve Linux is an arm port of an OS like Centos :).

#Logged in as pi user but startx doesnt work how to

The following video shows how to change from the Raspbian Jessie default of auto login to the desktop to auto login to the command prompt.I’ve got an updated version of RedSleeve Linux ( ) running on the Raspberry Pi. To start the desktop if settings are changed to boot to the command line, enter startx at the command prompt to start the desktop again. If you do enable the PI to boot up and require login, don't forget that the default user name is pi and the password is raspberry. This can be set by unchecking 'Login as user 'pi'' and selecting 'To CLI'. The default of the older Raspbian editions was to boot the Raspberry PI to the command line and require a user name and password to log in.

Selecting To CLI will boot the RPI to the command line interface.

Selecting To Desktop will boot the Raspberry PI to the graphical desktop.

If Login as user 'pi' is checked, you will not have to enter a user name or password when the operating system boots. Changing the Raspbian Jessie Auto Login Settings To automatically boot to the command line interface (CLI) at power-up, click the To CLI radio button and make sure that Login as user 'pi' is checked as shown in the image below. The Raspberry PI Configuration dialog box opens with the System tab selected. using putty on a windows machine or ssh pi on linux/mac os x) and then retrace the steps that created that mess in the first place (most likely editing rc. Login settings can be changed easily from the desktop.įrom the Raspbian desktop, choose Menu → Preferences → Raspberry PI Configuration by using the main menu button at the top left of the screen. however, you can still access your pi using ssh (e.g. Login Automatically to Raspbian JessieĪ new installation of Raspbian Jessie automatically logs in and starts the graphical desktop when the Raspberry PI is powered up. With the inittab file gone, the auto login settings can now be changed in the Raspberry PI configuration dialog box as explained in this article. Because of changes to the operating system, Raspbian Jessie no longer has an inittab file in /etc/. In fact, the Raspberry Pi and the BeagleBone Black boards are just about. In previous versions of Raspbian, the inittab file had to be modified to auto log in. TERMS OF USE This is a copyrighted work and McGraw-Hill Education and its.